Skip to content

chiara h4B

Luxled industrial lighting

CHIARA H with hanger bracket

chiara h4b

CHIARA H4B è la versione base di questa plafoniera. The aesthetics of the lamp are the same for all versions. CHIARA H4B, unlike the CHIARA H4BD version, however, is not equipped with electronic control.

With only 160 Wof power and a yield of 24,064 effective lumens, it is a very efficient ceiling light that can perfectly replace a 400W high pressure sodium ceiling light.

  1. 64 power LED
  2. front dissipation
  3. ultraclear optical SILICONE optics
  4. 3 different optics depending on the application
  5. reinforced aluminum front
  6. integrated power supply
  7. available in 4000k and 5000k temperatures
  8. 6 fixing solutions (see)
  9. Certification (see)

TECHNICAL DATA

CHIARA H4B ceiling light

DESCRIPTIONVALUE
AVERAGE POWER160W
SUPPLY VOLTAGE100 280 VAC 50/60 Hz
PFC0.99
LIGHT SOURCE64 POWER LED
NOMINAL FLOW OF LEDs25.600 lm
REFERENCE FLOW24.064 lm
COLOR TEMPERATURE4000K (5000K)
COLOR RENDERING80
LENSESSILICONE
OPTICSLARGE / EXTRA-LARGE
DIMENSIONS560X560X116 mm
MATERIALPA6.6 / ALUMINIUM L 5754
INSULATION CLASSI
WEIGHT6.5 KG
DEGREE OF PROTECTIONIP65
WORKING HUMIDITY0 98% R
LIFETIME> 60.000 h L80

OPTICS CHIARA H4B

FIND OUT HOW MANY LAMPS YOU NEED FOR YOUR ENVIRONMENT! REQUEST A LIGHTING PROJECT,IT’S FREE!

FILL OUT THE FORM BELOW

chiara h4bd

Luxled industrial lighting

chiara h4bD

CHIARA H4BD is the ADVANCED AND COMPLETE version of this ceiling light. The device, unlike CHIARA HB, is in fact equipped with electronic control. With the electronic control, the ceiling light can:

  • Self-dimming, no data cable or 0-10V control required, lamp by lamp. Dimming takes place thanks to a sensor placed in the center of the lamp that detects the ambient brightness and, depending on it, makes a gradual, fine and slow (for safety reasons) decrease in the luminous flux to adapt it to the detected ambient light. This sensor has been called by us precisely AUTODIMMER; the autodimmer allows, in industrial environments with skylights and windows, a saving of 25-30% compared to non-dimmed lighting, as well as obviously a longer life of the ceiling light.
  • The electronics on board the lamp also allows the control of the life of the LEDs, in fact these are, in the initial phase, slightly weakened and, in the phase of decay of the LED flux over the years, this weakening is gradually diminishing, I ask the lamp a CONSTANT FLOW with VARIABLE POWER.
  • The electronics also allow you to set a desired power, starting from the initial one set in the data sheet, if the customer wants a less powerful and less performing product in terms of light.
  • The electronics also allow interfacing, together with a suitable LED DRIVER, with DALI technology, if the customer is already equipped with industrial home automation.

CHIARA H4BD means investing in the future and starting saving immediately !!!

  1. 64 power LED
  2. front dissipation
  3. ultraclear optical SILICONE optics
  4. 5 different optics depending on the application
  5. reinforced aluminum front
  6. integrated power supply
  7. available in 4000k and 5000k temperatures
  8. SELF-DIMERATION
  9. CONSTANT FLOW at VARIABLE POWER
  10. DALI interfacing
  11. 6 fixing solutions (see)
  12. Certification (see)

TECHNICAL DATA

CHIARA H4bd ceiling light

DESCRIPTIONVALUE
AVERAGE POWER148W
SUPPLY VOLTAGE100 280 VAC 50/60 Hz
PFC0.99
LIGHT SOURCE64 POWER LED
NOMINAL FLOW OF LEDs25.600 lm
REFERENCE FLOW24.064 lm
COLOR TEMPERATURE4000K (5000K)
COLOR RENDERING80
LENSESSILICONE
OPTICSNARROW / MEDIUM / WIDE / EXTRA-WIDE / ASYMMETRIC
DIMENSIONS560X560X116 mm
MATERIALPA6.6 / ALUMINIUM L 5754
INSULATION CLASSI
WEIGHT6.5 KG
DEGREE OF PROTECTIONIP65
WORKING HUMIDITY0 98% R
LIFETIME> 60.000 h L80

CHIARA H4BD OPTICS

ARE YOU A DESIGNER?
DOWNLOAD OUR PHOTOMETRIC FILES!

THE Fixing SOLUTIONS

luxled industrial lighting, CHIARA H4B and CHIARA H4BD

CHIARA H4 is a lighting fixture, suitable for normal indoor use or under a roof, which can be installed on the wall or ceiling; in adherence or suspended; in a horizontal or inclined position no more than 20 °; at a height between 4m and 25m above the ground; in a position that can only be reached by qualified technical personnel. To install the CHIARA H4 appliance, the following solutions are basically envisaged.

HANGING AT BUSWAY

To suspend the CHIARA H4 luminaire from busway it is necessary to equip yourself with 2 hooks supplied by the busway manufacturer, suitable for the use and weight to be supported, and the standard bracket (photo opposite).

hanging from a beam or pierceable support

To fix the CHIARA H4luminaire to a beam or other support, these must be suitable for supporting the luminaire and the holes described in the installation manual can be drilled without compromising its stability (see standard bracket photo opposite).

hung with chains or cables

To hang the CHIARA H4 luminaire using chains or cables, use two holes located in the upper part of the standard bracket, inserting in each of these holes an M6 eyebolt fixed with a self-locking nut or with 2 M8 eyebolts fixed with a self-locking nut to the two side holes of the bracket.

hung from a beam or other support by means of a short adjustable counter-bracket

To fix the CHIARA H4 luminaire to a perforable beam or support and to have the possibility of orienting it on the horizontal plane, use the short counter-bracket, 50 mm, (photo opposite) which must always be combined with the standard bracket.

fixed to vertical or inclined wall by means of a long adjustable counter-bracket

To fix the CHIARA H4 appliance to a vertical or inclined wall or to distance it from a ceiling or other horizontal support, use the long counter-bracket (image on the side). The long counter-bracket, 300 mm, (to always be combined with the standard bracket, supplied as standard) must be fixed to the support material by means of suitable accessories suitable for the material itself, using at least 2 of the holes provided for this purpose on the bracket.

HANGING FROM CEILING, VERTICAL OR INCLINED WALL OR OTHER SUPPORT USING HANGER

For suspended installations that also require an aesthetic result, as well as a technical one, it is recommended to use the APPENDINO accessory supplied separately. The hanger allows the CHIARA H4 luminaire to be suspended by fixing it to the ceiling or other horizontal or inclined structures as long as they are suitable for supporting the luminaire and related stresses.

certifications

luxled industrial lighting, CHIARA HB and CHIARA H4BD

European standards include certain lighting and safety requirements at the same time. Regulatory compliance is unfortunately sometimes not sufficient to guarantee them. It is therefore important to certify your products. CHIARA H4, in addition to the electrical, EMC and photobiological certification, was also subjected to the salt spray test.

ELECTRICAL CERTIFICATION

chiara h electrical certification

EMC CERTIFICATION

CE CETIFICATION

SALINE FOG TEST

PHOTOBIOLOGICAL CERTIFICATION

CHIARA H PHOTOBIOLOGICAL CERTIFICATION

BEST PRODUCT AWARD

CHIARA H BEST PRODUCT AWARD

WANT MORE INFORMATION?

Send us an email (info@luxled.it) or fill out the form opposite, we will contact you as soon as possible!

This website uses technical and profiling cookies. Clicking on "Accept" authorises all profiling cookies. Clicking on "Refuse" or the X will refuse all profiling cookies. By clicking on "Customise" you can select which profiling cookies to activate.
Warning: some page functionalities could not work due to your privacy choices